AnsweredAssumed Answered

Re-naming of remote loads not possible in SW2014 sp3

Question asked by steve bywaters on Apr 24, 2014
Latest reply on Apr 30, 2014 by steve bywaters

Like • Show 0 Likes0
Comment • 5

I recently upgraded to SW2014 sp3 (64-bit) and find that in Simulation if I rename a remote load to something more meaningful, then edit the remote load and 'tick' to accept then the name of the remote load reverts back to the original default name. Renaming of other loads (pressure, force etc) is not affected. I've never had this issue on previous versions e.g. SW2013....has anyone else experienced this? I am also experiencing frequent short pauses during commands and slow "file opens" but I think that is a separate issue.

Justin Strempke Apr 29, 2014 7:18 PM

Correct Answer

Verified on same platform, both with you model and fresh one made up. Nothing in KB yet for SPR's, shoot it to your VAR.

See the reply in context

Attachments

loads1.PNG13.5 KB

No one else had this question

Outcomes

Jared Conway Apr 25, 2014 1:16 AM

All files?

All studies?

Can you post a file that is very simple that shows the issue? A block?

Actions

steve bywaters @ Jared Conway on Apr 25, 2014 4:37 AM

Thanks Jared, see attached simple static study.

When I re-name " Remote Load (Direct transfer)-4 " to something else, then edit definition, and finally accept (tick) then the name will default back to what it was before it was re-named.

Attachments

Part1.SLDPRT.zip64.5 KB

Actions

Jared Conway @ steve bywaters on Apr 26, 2014 2:12 AM

If it happens on all models and comps in the latest version, report to yor reseller.

Actions

Justin Strempke @ steve bywaters on Apr 29, 2014 7:18 PM

Verified on same platform, both with you model and fresh one made up. Nothing in KB yet for SPR's, shoot it to your VAR.

Actions

steve bywaters @ Justin Strempke on Apr 30, 2014 4:25 AM

Thanks for verifying Justin. Have already contacted my VAR.

Actions

5 Replies

Jared Conway Apr 25, 2014 1:16 AM
Mark Correct
Correct Answer
All files?

All studies?

Can you post a file that is very simple that shows the issue? A block?
Like • Show 0 Likes0
Actions
- steve bywaters @ Jared Conway on Apr 25, 2014 4:37 AM
  Mark Correct
  Correct Answer
  Thanks Jared, see attached simple static study.
  
  When I re-name " Remote Load (Direct transfer)-4 " to something else, then edit definition, and finally accept (tick) then the name will default back to what it was before it was re-named.
  Attachments
  - Part1.SLDPRT.zip64.5 KB
  Like • Show 0 Likes0
  Actions
  - Jared Conway @ steve bywaters on Apr 26, 2014 2:12 AM
    Mark Correct
    Correct Answer
    If it happens on all models and comps in the latest version, report to yor reseller.
    Like • Show 0 Likes0
    Actions
  - Justin Strempke @ steve bywaters on Apr 29, 2014 7:18 PM
    Unmark Correct
    Correct Answer
    Verified on same platform, both with you model and fresh one made up. Nothing in KB yet for SPR's, shoot it to your VAR.
    Like • Show 1 Like1
    Actions
    - steve bywaters @ Justin Strempke on Apr 30, 2014 4:25 AM
      Mark Correct
      Correct Answer
      Thanks for verifying Justin. Have already contacted my VAR.
      Like • Show 0 Likes0
      Actions

Re-naming of remote loads not possible in SW2014 sp3

Attachments

Outcomes

Attachments

Related Content

Recommended Content