• How to flatten sweep flange sheet metal with concentric cylinders?

    I want to create a sheet metal part consisting of two concentric cylinders using sweep feature like this: But I don't know how to flatten it. If the transition between cylinders is vertical, the flatten w...
    Louise Yi
    last modified by Louise Yi
  • Curved folded

    117/5000 Hello, I try to make these forms in solidworks. Has anyone else encountered such forms? I don't know how to approach it example 01 example 02 Thank you.
    Dragos Popovici
    last modified by Dragos Popovici
  • How to connect a cylinder with a flat plate and flatten all parts?

    I want to connect a cylinder/tube with a flat plate and then flatten all of them. The picture below is what I get with non-sheet metal features. But I don't know how to achieve them in sheet metal.    For...
    Louise Yi
    last modified by Louise Yi
  • Easy way to make 360 deg?

    What the easiest way to make this go 360 deg?
    Scott Leacox
    last modified by Scott Leacox
  • Sheet metal corner problem

    Attached is a file and screen shot of a problem sheet metal corner.   My goal is to fill in a small notch of a sheet metal corner. Other than that notch the design is as desired. What is the path of least resis...
    Scott Leacox
    last modified by Scott Leacox
  • Sheet Metal Flange Error

    Hello all, Shouldn't the program fix this part automatically? Why is it constructed incorrectly and I have to fix it every time. If this is my ignorance, please inform me!     Best regards, Öm...
    ömür tokman
    last modified by ömür tokman
  • How: different relief type on both sides of an edge flange

    Hello Guys, I would like to have tear-extend type on left side and tear,obround whatever on right side. Is it possible? I sit on 2019sp4. The bottom picture shows preview, but I get an error.  
    Michal Lamentowicz
    last modified by Michal Lamentowicz
  • Only some of my bend lines are showing on my part and not others

    In one of my steel parts there are 4 bends. I have updated this part and as such have unfolded, then modified, and then folded the part again. Now when I click on flatten, it only shows the bend lines for 2 of the ben...
    Evan Hughes
    last modified by Evan Hughes
  • Flatten sheet metal in a multibody part

    Hello all //referring to the file attached.   I am trying to flatten the sheet metal cylinder that has extruded cuts in it. But it won't flatten properly. Could this be because its a multi-body part?   In...
    Zach Sycks
    last modified by Zach Sycks
  • PEM features from SolidWorks design library in Sheetmetal parts

    We are starting to use the PEM features from the SolidWorks design library in our sheetmetal parts (SLDPRT). We are doing this instead of making an assembly of the sheetmetal and inserting separate models of PEM capti...
    Carrie Ives
    last modified by Carrie Ives
  • convert letters

    I am working on a model for some large letters that are going to be built and installed on our campus. I have the font sized correctly and extruded using a thin feature and capped the ends to create the letters as (fo...
    Derek Goodson
    last modified by Derek Goodson
  • Sheet metal bend groove?

    Doing a simple sheet metal bend, is it possible to add a groove/guide where the bend is, almost like a trench all along where the bend is to help when the bend is done in real life?
    Charlie Stanley
    last modified by Charlie Stanley
  • Copper ball segments FEA

    I'm looking at making a 400mm ball from copper, Is there anyway in simulation or in sheet metal to calculate when the material will tear. can I make the ball in two sections or will it need 10 segments? I ca...
    Laurence Turner
    last modified by Laurence Turner
  • Threaded sheet metal emboss?

    Is there a preferred method for creating threaded embossed features in sheet metal, to accept screws without using PEMs?  The attached shots are of a metal junction box and kind of what I'm trying to achieve, for...
    Garet Holcomb
    last modified by Garet Holcomb
  • Flattened Part Unflattening Itself When I Click Away

    All,    I am having an issue where when I flatten an edge flange it flattens fine until I click away from the document, save and re-open the document, or try to make any changes to the document. So, pretty ...
    Kyle Singh
    last modified by Kyle Singh
  • Sweep Flange Flatten not working?

    Hi all,   I have a imported solid I am tasked to remodel and make into a sheet metal part that can be flattened so we can cut out on a laser machine.   dumb solid:     now I have attempted to ...
    Jim Moses
    last modified by Jim Moses
  • Help with flattening tapered section

    I am using solid works 2019 with a student license, In a university student project (FSAE). I am drawing a tapered sheet section that needs to be flattened so we can cut it out on our router. It is largely defined b...
    Bradley Wilkinson
    last modified by Bradley Wilkinson
  • FOLD ERROR ON CUT EXTRUDE ON SWEPT FLANGE

    Hello, I'm trying to recreate the part similar to creo part below. I have an error with fold in the next image.     Fold error below. See next image for detail of error.     Cut extrude se...
    John Jordan
    last modified by John Jordan
  • Flatten a part created with shell that has compound bends

    Hi all,   I have a part that I have tried to create several ways using sheet metal, form tools and finally this shell and then creating a sheet metal part. Am I asking Solidworks to do something it wont do or wh...
    Jim Moses
    last modified by Jim Moses
  • Linking cut-list properties to custom properties

    I need to link some of my custom properties to cut-list properties. For parts created by SW2018 it works fine, I just use "SW-Bounding Box Length@@@CutList@@Configuration Name@Filename.SLDPRT" variable and see ac...
    Anatoliy Jukov
    last modified by Anatoliy Jukov